Brake Hoses Unlimited - Ford Country Squire - 1969, 1970 - Front Disc. Your Source for Brake & Clutch Hoses. Vintage - Classic - Custom. 1920's - 1930's - 1940's - 1950's - 1960's - 1970's. If you don't find what you are looking for just ask.2 Front Hoses & 1 Rear Hose. Ford Country Squire - 1969, 1970. To check if your Country Squire has the WER rear axle look at the rear brake hose. If it is attached with one bolt it is WER.
If it is attached with two bolts like the rear hose in the picture below it is NOT a WER rear axle. These are BRAND NEW freshly made hoses. You order them we make them. Guaranteed to be 100% accurate for the application listed. No Grinding, Cutting or extra Adapters needed.Our brake hoses are made to replace the stock OEM hoses. If your vehicle has had a Disc Brake Conversion Kit or your vehicle has been Converted to a newer style disc brake set-up than what came on the vehicle this set WILL NOT FIT. We build Custom hoses all the time so making what you need will not be a problem. We can make almost a. Ny Brake or Clutch Hose to suit any type of vehicle. All Hoses we make are D. Compliant and meet or exceed International safety standards for brake hoses. Which can put you and your vehicle at risk. Every hose is pressure tested to 3000psi. Oth Rubber & Braided Stainless Steel hoses. (Stainless Steel Braided do cost more than Rubber). All of the hoses we make will install in the vehicle just like the factory hoses. Unused Condition with all packaging. All you need to do is read the listing and you will see that NO reference is made that the brake hoses are D. Brake hoses used in the USA must be D.
T Certified to be Street Legal. Are your Brake Hoses D.
Certified and Legal for use in the USA? Are your Brake hoses D. We have been approved and given a registration number by the D. All brake hoses manufactured with the equipment we use and the components meet or exceed D. T FMVSS106 and SAE J1401 standards.Our brake hoses meet all International Safety Standards and have all the proper labeling on the hoses to pass Vehicle Inspections in any State or Country. Why should I care if the brake hoses are D. When a brake hose has D. Certification it means that the Equipment, Parts and Process all met the requirements to make a safe brake hose. Approved which makes them illegal to use in the USA.
Are you risking your Life, Vehicle and Family with cheap brake hoses?? How are the brake hoses identified as being D. All the brake hoses we make must have our D.
Number crimped into the fitting when made. The brake hoses are also D. Labeled and date coded per regulations. So at any time, no matter where our brake hoses go, they can be traced back to us.If I have a problem with a brake hose what do I need to do? Once it arrives we first make sure it is our hose by the D. Number in the crimp area.
It will then be examined and we will contact you on what conclusion we came to and what we can do resolve the problem. Why do you have to have the PVC Cover on the hoses?
Determined that the Braided Stainless Brake Hoses used for Street use needed to have a coating to protect the inner Teflon tube. It was found that dirt particles were working through the uncovered stainless braid and getting down to the Teflon inner tube. Then as the hoses moved it acted like sand paper and wore away the inner tube causing failure. What is a Whip Insert?The Whip Insert is placed on the end of the Braided Stainless Brake Hose before we place the fitting on for crimping. The Insert is made with a special aluminum that is a buffer between the stainless hose and steel fitting. This is required to prevent premature hose wear if there is any side movement (Whip) as the hose is used, being a softer material it buffers some of the motion. If you have steel on steel the hose would wear out prematurely. There is actually a D. T "Whip Test" that our process and hoses had to pass before we were allowed to make Street Legal Braided Stainless Hoses. We carry a product liability policy that we must have in order to make and sell brake hoses. Do you test your hoses?
All hoses are pressure tested to 3000 psi, twice the maximum operating pressure of any normal vehicle. Do you make Custom hoses?Yes, we can make almost any brake hose configuration you need to make your Custom or Rod look great. No need in having a brake hose that is to long or to short, or a bunch of hodgepodge adapters to make it fit.
Normally how long does a brake hose last? The average life expectancy of a brake hose is about six years once it is put into service. This is based on a daily driven vehicle. So the less you drive a vehicle the longer the brake hoses will last. Do you make Stainless Steel Braided Hoses?
Yes, We can make almost any brake hose in either Rubber or Braided Stainless Steel. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts & Accessories\Brakes & Brake Parts\Brake Hoses, Lines & Fittings".
The seller is "goodbrakes" and is located in this country: US. This item can be shipped worldwide.