Crown Victoria Rear Suspension Trailing Arms 79-97 LTD Adjustable Grand Marquis

  

This kit comes with 2 Upper Rear Trailing Arms, 2 Lower Rear Trailing Arms, an Installation Manual, and a Full Install DVD. These Ford Crown Vic rear trailing arms fit a variety of applications based on the Ford Panther platform. For more information on the fitment applications for these rear trailing arms, check out the fitment guide table in the full description.

When lifting the rear of 79-97 Ford Panther platform vehicles, the trailing arms become too short to work efficiently. UCL extended rear trailing arms will greatly improve the performance of your lifted car application and are a necessity when raising the rear.

Crown Victoria rear suspension trailing arms 79-97 LTD adjustable Grand Marquis. 2 x Upper rear trailing arms. 2 x Lower rear trailing arms. SKU: RA-6070 CATEGORY: Crown Vic Lift Kit.

Crown Victoria Rear Suspension Trailing Arms for your 79-97 Ford Panther platform lift kit project. Are you planning on putting a lift in the rear of your 79-97 Ford Panther platform? These Crown Victoria Rear Suspension Trailing Arms fit all 79-97 Ford Panther platform cars and are a necessity when lifting the rear of this car. These rear arms fit the following vehicles from 1979 to 1997: Ford Crown Victoria, 79-91 Ford LTD, Ford Crown Vic, Ford Country Squire, 1980 Lincoln Continental, 80-83 Lincoln Mark VI, 81-97 Lincoln Town Car, Mercury Colony Park, and Mercury Grand Marquis.

See fitment table below for a full list of applications. The arms are a bolt-on design and are specifically designed for cars running lift springs or lift cups.

Why do I need longer Crown Victoria Rear Suspension Trailing Arms when lifting my car? UCL extended rear trailing arms will solve many problems associated with running lift springs or lift cups such as the following. Drive shaft angle, also know as pinion angle, being out of alignment. Premature U joint failure, causing an unsafe driving condition.

Wheels moving forward into the wheel well and looking funny. Universal Car Lifts Crown Victoria Rear Suspension Trailing Arms fit all 79-97 Ford Panther platform vehicles. They will greatly improve the performance of your lifted car application and are a necessity when raising the rear.

They will also improve the appearance of the car and get rid of the issues associated with the wheel moving forward. For this reason, we highly recommend running these arms when lifting your Crown Vic, Grand Marquis, Lincoln Town Car, Crown Victoria, Colony Park, Country Squire or any other 79-97 Ford Panther platform application. How are UCL's Crown Victoria Rear Suspension Trailing Arms different from others? Our longer trailing arms are the most durable on the market and are rated for over 1000hp. Constructed from high grade steel that is precision machined to exacting tolerances, UCL arms are over-sized and over-built for maximum performance. Massive 1-3/4 tubing construction is the largest in the industry to handle maximum abuse. Arms are adjustable up to 3 inches over stock trailing arms. Threaded adjustments allow you to fine tune your drive shaft angle to eliminate vibrations.

Upper and lower arms include high grade plated jam nuts for corrosion resistance. Precision machined bushing receivers for a guaranteed accurate bushing fit. Welded by certified welders using state of the art equipment.

Finished in a durable gloss black powder coat finish for years of trouble free use. Rest assured that by purchasing UCL Crown Victoria Rear Suspension Trailing Arms, you are purchasing the best car lift products in the world.

Durable gloss black powder coating lasts 100x longer than spray painted parts. When choosing Crown Victoria Rear Suspension Trailing Arms for your car lift project, be sure to note the finish on the parts. All of Universal Car Lifts parts feature a durable gloss black powder coat finish.

We start by cleaning the raw metal parts with a degreaser solution to facilitate a permanent finish bonding. The parts are then sent through a large oven and heated to encourage off gassing. This uniformly bakes off any impurities from the parts.

After pretreating the parts in an oven, the Crown Victoria Rear Suspension Trailing Arms are professionally sprayed with a high end powder coat gun in a clean room spray booth. The arms are then sent back through the oven where they bake at the proper temperature to obtain a permanent bond.

This powder coat technique is the same method that new car manufacturers use to ensure their parts last virtually forever. It prevents rust from forming on the parts which will weaken the steel and cause premature failure. Beware of "knock-off brand" sellers who use cheap hardware store spray paint to finish their parts. The finish will look like crap and the parts will almost immediately rust.

The corrosion will eventually cause the parts to fail and could cause your rear end to fall out of your car. Insist on genuine UCL Crown Victoria Rear Suspension Trailing Arms for your project.

We have been manufacturing car lifts longer than anyone else and have more cars running our lifts than anyone else. Bushing options for your 79-97 Crown Victoria Rear Suspension Trailing Arms. Like all car lift kits, you will need to install new bushings in to the trailing arms. You can try reusing your stock bushings, but chances are the 20+ year old factory units are in need of replacement.

As an alternate option, we can supply the bushings for you. You will need to use a hydraulic H press to install the bushings in the rear trailing arms. We recommend having an experienced professional do this. If you are interested in having us install the bushings for you, we can send you the trailing arms with them fully installed and ready to bolt on your ride.

This includes all new bushings and professional installation. Most customers agree this is by far the easiest way to get your car up and rolling the fastest. We beat all competitors prices on identical products. We are confident our products are the best quality at the best prices. If you find a better price on an identical product, we will gladly beat it. UCL has lifted more cars than anyone else and was the first company to offer car lift kits. Our customers have been riding high on our products for over 15 years. If the product fails just let us know and we will immediately send you a replacement free of charge.

Getting your Crown Victoria Rear Suspension Trailing Arms installed quickly and trouble free on your 79-97 Ford Panther platform is important. For this reason, we include an installation DVD that shows step-by-step how to install your products. We also include a printed installation manual. We want your installation to be effortless.

That is why we have experienced technicians on staff extended hours to make sure everything goes smoothly. You should see our number listed.

You can also look us up online. Great price will do business again. Customer vehicles with Universal Car Lifts kit installed.

Want more info on which kit these cars are running? How to Install Car Lift Kits. The item "Crown Victoria Rear Suspension Trailing Arms 79-97 LTD Adjustable Grand Marquis" is in sale since Sunday, October 28, 2018.

This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Suspension & Steering\Lift Kits & Parts". The seller is "carliftkits" and is located in Saint Joseph, Minnesota. This item can be shipped to United States, Canada.

• Modified Item: No
• Country/Region of Manufacture: United States
• Custom Bundle: Yes
• Adjustable: Yes
• Manufacturer Part Number: RA-6070
• Included Hardware: Rear Trailing Arms
• Position: Rear
• Placement on Vehicle: Left
• Brand: UCL
• Fitment Type: Performance/Custom
• Non-Domestic Product: No
• Warranty: Lifetime
• Bundle Description: 2 x Upper rear trailing arms, 2 x Lower rear trailing arms, Installation manual, Full install DVD