It uses metering rods to transition between circuits, Features bolt-on-and-run performance right out of the box, Provides smooth throttle response throughout the power band, The float levels are factory set and adjustments are rarely needed, A two-piece design means no gaskets below the fuel level for leak-free operation. Edelbrock 1404 Performer 500 CFM 4 Barrel Carburetor, Manual Choke. Edelbrock Performer Series 4 barrel carbs have proven themselves to be easy to tune with great drivability. Whether you need to replace an aging stock carb or are looking for a performance four barrel carb to top off your hot rod, the Edelbrock Performer Series 4 barrel carbs are the best choice for performance and value.
All Edelbrock parts are proudly made in the U. This 500 CFM four barrel carburetor is designed and calibrated for small cubic-inch engines such as 305 c. D and smaller Chevrolet; 302 c.
Match with an Edelbrock Performer or Performer EPS manifold and other brands of similar design. Includes manual choke and detailed instructions.
Bolt-on-and-run performance right out of the box. Smooth throttle response throughout the power band. Uses metering rods to transition between circuits - rods can be changed in seconds without carburetor removal or draining fuel. Float levels are factory set; adjustments are rarely needed.
Change jets, adjust floats & replace needles/seats without draining fuel or removing carb. Two-piece design means no gaskets below the fuel level for leak-free operation. Lightweight all-aluminum body is compatible with gasohol and blended fuels. Includes both timed and full vacuum ports for ignition advance. Step-Up Spring - orange (5 Hg). 3-1/4 from bottom of carb base to the base of the carb neck. Mounting bolt hole pattern is 5-1/8" by 5-5/8". 5.160" x 5.625". By Mike on September 23, 2021.Super easy to install and tune. Yes, I recommend this product.
By 27 ratrod on September 28, 2020. Everything I ordered fit well....... Carb, adapter, throttle and choke cable, etc. What more can I say.By Dave on June 08, 2020. Couldn't get my rat rod to run at all, tried everything, had an old Holley 600 on it so I decided to give this 500 a shot.
Bolted it on, started the car, it ran ok, set the timing and the car came to life and ran beautiful. Right out of the box ready to go, no adjustments needed. By Santieos on November 20, 2018. Thank you, very good experience. I'm from Barcelona, but it has been very easy and convenient.This is the second one i have used. By Jim K on December 19, 2017.
This is a real good choice for a mild 300 ci engine, Installed and drive, only had to adjust idle mix, and speed. Related Items / Suggested Parts. Edelbrock 1405 Performer 600 CFM 4 Barrel Carburetor, Manual Choke.Edelbrock 1403 Performer 500 CFM 4 Barrel Carburetor, Electric Choke. Lokar TCB-40DQ Throttle & Kickdown Cable Bracket for Edelbrock Carbs. Edelbrock 1486 Performer Carburetor Calibration Kit, 1403 and 1404. Lokar TCB-40DQ1 Edelbrock Throttle Cable Bracket/Springs, Progressive.
Lokar XTCB-40DQ1 Black Edelbrock Thottle Cable Bracket/Springs. Edelbrock 1478 Performer Series Electric Choke Conversion Kit. Edelbrock 1477 Performer Carburetor Rebuild Kit. Edelbrock 8126 Performer Carb Fuel Line Kit, 3/8 Inch Hose Barb Inlet. Speedway Motors is America's Oldest Speed Shop® and has been a trusted source for specialty rodding and racing products and friendly expert advice for more than 72 years.